FANUC M-710iC/50

The FANUC M-710iC/50 price is available by quotation and depends on controller, tool, environmental options and complete system integration. The installed cost may include gripper or process spindle, force sensor, vision, fixtures, safety, PLC, machine interfaces, programming and acceptance. The robot arm is only one part of the investment. A usable industrial robot cell may also require the controller, FlexPendant or operator interface, pedestal, end effector, dress pack, vision, fixtures, safety equipment, PLC and fieldbus integration, guarding, programming, installation, training and production acceptance. Freight, taxes, customs, spare parts and local support can also change the delivered cost.

Before comparing offers, confirm the exact variant, controller generation, condition, included equipment, software licences and service responsibilities. The better buying question is: what is included, what performance is guaranteed, and who supports the complete cell?

You can request FANUC M-710iC/50 pricing or a complete automation quote through Anton Robots before committing.

You can buy or request the FANUC M-710iC/50 through Anton Robots. Anton Robots helps industrial buyers verify the genuine commercial route, compare new, used, refurbished or integrator-built packages and determine whether the FANUC M-710iC/50 matches the payload, reach and process. M-710iC/50 remains an active FANUC medium-payload industrial robot with current product and quote pages.

Before buying, confirm the exact robot variant, serial number where applicable, controller, RobotWare version, mounting orientation, environmental protection, end effector, process equipment, safety architecture, shipping, warranty and commissioning. A bare manipulator listing is not the same as a production-ready cell. Professional buyers should compare the total installed system, production target and support route rather than only the lowest displayed robot price.

To start, request FANUC M-710iC/50 buying or sourcing guidance through Anton Robots.

You can find the FANUC M-710iC/50 for sale through FANUC, authorised integrators, distributors and Anton Robots. Finding a FANUC M-710iC/50 for sale is only the first step. Buyers should verify whether the offer is a new supported robot, an integrator package, remaining stock, a used manipulator, a refurbished system or an incomplete arm without the correct controller and software. Confirm controller, mounting, IP option, dress pack, hours for used units, tool, software, safety, warranty and integration scope.

A useful comparison should cover the exact payload and reach variant, controller generation, operating hours, maintenance, calibration, batteries, cables, tooling, safety hardware, delivery, commissioning and warranty. Avoid treating a marketplace listing as proof that ABB will support the exact serial number or configuration.

If you are evaluating a FANUC M-710iC/50, contact Anton Robots. We can also compare it with other robotic arms for the same application.

Yes. You can request a FANUC M-710iC/50 quote through Anton Robots. A useful quote should identify the exact robot variant, controller, operator interface, RobotWare options, cabling, mounting, protection class, freight, warranty and available support. The proposal should define tool and part mass, reach, forces, path, cycle, mounting, environment, fixtures, machine interfaces, safety and acceptance.

The supplier also needs the part weight and dimensions, tool mass and centre of gravity, required reach, cycle time, accuracy, process equipment, floor layout, utilities, communications and safety constraints. This allows the proposal to be based on the real application rather than a generic arm price. Ask for a clear statement of integration scope, production acceptance test, exclusions, delivery milestones and responsibility after commissioning.

Anton Robots can help compare the FANUC M-710iC/50 against other industrial robot arms and prepare a package around the actual task.

A typical FANUC M-710iC/50 package may include the six-axis arm, R-30iB Plus controller, teach pendant, robot cables, software and selected process equipment. The exact contents vary by country, controller generation, integrator and application, so buyers should request a written bill of supply:

• FANUC M-710iC/50 robot
• R-30iB Plus controller and pendant
• Robot and power cables
• Pedestal or inverted mounting structure
• Gripper, spindle, dispenser or washing tool
• iRVision or force-sensor package
• Fixtures, PLC, fieldbus and safety system
• Programming, installation, training and support

The process tool, dust or fluid management, fixtures and safety cell are normally application-specific. End effectors and integration are especially important. The same robot can be configured for welding, machine tending, palletizing, handling, dispensing or assembly, but each task needs different tooling, fixtures, process equipment and safety validation. A low robot-only price may exclude most of what makes the system productive.

You can request an itemised FANUC M-710iC/50 package quote through Anton Robots before approving the cell.

The M-710iC/50 has a 50 kg payload, 2,050 mm reach and ±0.03 mm repeatability. FANUC lists six axes, an approximately 560 kg mechanical weight and about 3 kW average power consumption. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. The 50 kg includes the complete tool and part, while allowable inertia and centre of gravity remain critical.

Before buying or integrating the robot, verify tool and part mass, centre of gravity, wrist moments, reach, path, mounting and cycle. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Use FANUC load diagrams for the final configuration.

You can request FANUC M-710iC/50 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

M-710iC/50 supports material handling, machine tending, grinding, polishing, deburring, washing, waterjet, dispensing and inspection. Its payload, reach and rigidity make it a broad general-purpose platform across automotive and general industry. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. Every process requires different tooling, utilities, environmental controls, fixtures and safety design.

Before buying or integrating the robot, verify process, forces, dust or fluid, tool, payload, reach, cycle, quality, utilities and acceptance criteria. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Buy an engineered process cell rather than only the arm.

You can request FANUC M-710iC/50 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

Yes, FANUC lists floor, angle and inverted mounting. This flexibility allows the robot to work above machines, conveyors and process areas while preserving floor space. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. The supporting structure must handle the robot and dynamic loads and maintain safe service access.

Before buying or integrating the robot, verify mounting orientation, frame, bolts, reach, deflection, cables, maintenance, collision envelope and safety. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Use ROBOGUIDE and certified structural engineering.

You can request FANUC M-710iC/50 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

Yes, its mechanical rigidity and optional FANUC force sensing make it suitable for controlled finishing processes. Force control can help maintain contact pressure while the robot follows complex paths around castings or machined parts. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. Tool compliance, abrasive wear, dust, part variation and fixturing can dominate quality and cycle time.

Before buying or integrating the robot, verify required force, spindle, abrasive, fixture, dust extraction, path tolerance, tool change, wear compensation and trials. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Validate the process with real parts and consumables.

You can request FANUC M-710iC/50 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

The robot has IP54 body protection with IP67 optional and IP67 at the wrist and J3 arm. This supports many machining, washing and general industrial applications when the correct configuration is selected. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. The tool, cables, controller and added sensors may not share the same rating.

Before buying or integrating the robot, verify exact robot option, fluid, dust, temperature, cleaning, connectors, process tool and warranty conditions. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Specify environmental exposure before ordering.

You can request FANUC M-710iC/50 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

The M-710iC/50 is the established current C-generation model, while newer M-710 variants may offer updated mechanics, controller support or application features. Both target medium-payload general industry and can overlap in handling and processing tasks. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. Availability and exact specifications vary by region and model suffix.

Before buying or integrating the robot, verify payload, reach, footprint, mounting, repeatability, controller, IP rating, cycle, support and price. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Compare the current region-specific catalogue and cell simulation.

You can request FANUC M-710iC/50 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

Choose M-710iC/50 for 50 kg flexible processing and R-2000iC/165F for much heavier 165 kg handling and spot welding. The R-2000 offers higher payload and 2.655 m reach but is substantially heavier and more expensive to integrate. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. Oversizing increases floor, tooling, energy and safety cost, while undersizing can invalidate load and cycle targets.

Before buying or integrating the robot, verify tool and part mass, reach, inertia, process forces, cycle, floor space, mounting and future products. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Select the smallest robot with sufficient margin.

You can request FANUC M-710iC/50 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

The FANUC M-710iC/50 can be supplied internationally through FANUC and authorised system integrators. Industrial robot delivery depends on the destination country, robot condition, controller, freight method, export rules, customs and local service coverage. Confirm controller standard, industrial freight, mounting, local service, process equipment and commissioning responsibility.

Before ordering, confirm who disconnects, preserves, packs, lifts, insures, imports, installs, anchors, reconnects, calibrates and recommissions the system. Used robots should be shipped with transport restraints, controller cabinets, FlexPendant, cables, backups and maintenance records. A robot that can physically be transported is not necessarily supported or ready for production in another country.

You can request international availability for the FANUC M-710iC/50 through Anton Robots so the complete delivery and commissioning route can be checked. Buyers should obtain written confirmation of these points before approving a budget, purchase order, integration project, or production deployment.

FANUC M-710iC/50 availability and lead time can change according to model status, variant, controller, options, integrator capacity and destination. The model is current, while controller, options, tooling and integrator capacity determine total project delivery.

Before committing to a production date, ask whether the robot is factory ordered, remaining stock, used, refurbished or already allocated, and whether the controller, tooling, safety system and integration resources share the same schedule. Cell design, RobotStudio simulation, manufacturing of fixtures, software, factory acceptance testing, freight, installation and site acceptance often take longer than obtaining the arm itself. You can request current FANUC M-710iC/50 availability and project lead time through Anton Robots.

Buyers should obtain written confirmation of these points before approving a budget, purchase order, integration project, or production deployment. Buyers should obtain written confirmation of these points before approving a budget, purchase order, integration project, or production deployment.

Before buying the FANUC M-710iC/50, check the warranty or refurbishment guarantee, covered components, service territory, repair process, software entitlement, spare-parts availability and who supports the integrated cell. Confirm FANUC coverage for robot and controller and integrator coverage for spindle, gripper, force sensor, fixtures, PLC and safety. Ask:

• Is the manipulator, controller, FlexPendant and process equipment covered?
• Who handles diagnostics, calibration, repairs and replacement parts?
• Are RobotWare licences, backups and RobotStudio files transferred?
• Are preventive maintenance, grease, batteries and dress packs included?
• Who supports the gripper, welder, vision, PLC and safety system?
• What response time and production-recovery commitment is provided?

For a legacy robot, serial-number support and spare-parts horizon are primary buying criteria. Contact Anton Robots to review the complete package. Buyers should obtain written confirmation of these points before approving a budget, purchase order, integration project, or production deployment.

The FANUC M-710iC/50 is worth considering if you need a robust current 50 kg general-purpose robot for handling, machine tending or force-controlled processing. Its strongest value comes from its 2.05 m reach, repeatability, mounting flexibility, high rigidity and mature FANUC vision and force ecosystem.

However, a robot arm only creates value when the task, tool, fixture, controller, safety design, cycle time and support are correctly engineered. It requires a safeguarded industrial cell and can be oversized for light parts or undersized for heavy automotive tooling.

Buyers should compare total installed cost, expected throughput, quality, uptime, maintenance, energy, changeover and remaining product life rather than only payload and purchase price. For a legacy unit, a low acquisition cost can be outweighed by integration, batteries, calibration, parts and downtime risk. Compare other robotic arms and request application advice through Anton Robots.