FANUC M-410iC/185

The FANUC M-410iC/185 price is available by quotation because the relevant investment is the complete palletizing cell rather than the robot-only price. The project may include gripper, conveyor interfaces, pallet dispenser, slip-sheet handling, vision, safety, PLC, programming and acceptance. The robot arm is only one part of the investment. A usable industrial robot cell may also require the controller, FlexPendant or operator interface, pedestal, end effector, dress pack, vision, fixtures, safety equipment, PLC and fieldbus integration, guarding, programming, installation, training and production acceptance. Freight, taxes, customs, spare parts and local support can also change the delivered cost.

Before comparing offers, confirm the exact variant, controller generation, condition, included equipment, software licences and service responsibilities. The better buying question is: what is included, what performance is guaranteed, and who supports the complete cell?

You can request FANUC M-410iC/185 pricing or a complete automation quote through Anton Robots before committing.

You can buy or request the FANUC M-410iC/185 through Anton Robots. Anton Robots helps industrial buyers verify the genuine commercial route, compare new, used, refurbished or integrator-built packages and determine whether the FANUC M-410iC/185 matches the payload, reach and process. M-410iC/185 remains an active FANUC palletizing robot with a current product page and quote route.

Before buying, confirm the exact robot variant, serial number where applicable, controller, RobotWare version, mounting orientation, environmental protection, end effector, process equipment, safety architecture, shipping, warranty and commissioning. A bare manipulator listing is not the same as a production-ready cell. Professional buyers should compare the total installed system, production target and support route rather than only the lowest displayed robot price.

To start, request FANUC M-410iC/185 buying or sourcing guidance through Anton Robots.

You can find the FANUC M-410iC/185 for sale through FANUC, authorised palletizing integrators and Anton Robots. Finding a FANUC M-410iC/185 for sale is only the first step. Buyers should verify whether the offer is a new supported robot, an integrator package, remaining stock, a used manipulator, a refurbished system or an incomplete arm without the correct controller and software. Confirm controller, gripper, product range, pallet pattern, conveyors, condition, software, safety, warranty and integration scope.

A useful comparison should cover the exact payload and reach variant, controller generation, operating hours, maintenance, calibration, batteries, cables, tooling, safety hardware, delivery, commissioning and warranty. Avoid treating a marketplace listing as proof that ABB will support the exact serial number or configuration.

If you are evaluating a FANUC M-410iC/185, contact Anton Robots. We can also compare it with other robotic arms for the same application.

Yes. You can request a FANUC M-410iC/185 palletizing quote through Anton Robots. A useful quote should identify the exact robot variant, controller, operator interface, RobotWare options, cabling, mounting, protection class, freight, warranty and available support. The proposal should define product sizes and weights, pallet pattern, stack height, infeed, throughput, gripper, pallet handling, safety and acceptance.

The supplier also needs the part weight and dimensions, tool mass and centre of gravity, required reach, cycle time, accuracy, process equipment, floor layout, utilities, communications and safety constraints. This allows the proposal to be based on the real application rather than a generic arm price. Ask for a clear statement of integration scope, production acceptance test, exclusions, delivery milestones and responsibility after commissioning.

Anton Robots can help compare the FANUC M-410iC/185 against other industrial robot arms and prepare a package around the actual task.

A typical FANUC M-410iC/185 package may include the four-axis robot, R-30iB Plus controller, pendant, cables, palletizing software and selected end-of-line equipment. The exact contents vary by country, controller generation, integrator and application, so buyers should request a written bill of supply:

• FANUC M-410iC/185 palletizing robot
• R-30iB Plus controller and pendant
• Robot and power cables
• Heavy vacuum, clamp or servo gripper
• Conveyor, product and pallet interfaces
• Pallet dispenser or slip-sheet equipment
• PLC, guarding, scanners and safety system
• Programming, installation, training and support

Product handling, gripper, pallet stations and conveyor logic determine whether the robot achieves the required throughput. End effectors and integration are especially important. The same robot can be configured for welding, machine tending, palletizing, handling, dispensing or assembly, but each task needs different tooling, fixtures, process equipment and safety validation. A low robot-only price may exclude most of what makes the system productive.

You can request an itemised FANUC M-410iC/185 package quote through Anton Robots before approving the cell.

The M-410iC/185 has a 185 kg payload and 3,143 mm reach. FANUC lists four axes, ±0.05 mm repeatability, approximately 1,330 kg mechanical weight and 3 kW average power consumption. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. The payload includes the gripper and product, while centre of gravity and inertia affect cycle and allowable motion.

Before buying or integrating the robot, verify gripper and product mass, centre of gravity, inertia, pallet height, reach, cycle and load diagram. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Size the cell around the heaviest actual pick.

You can request FANUC M-410iC/185 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

The four-axis layout is optimised for fast palletizing and vertical stacking. It provides base rotation, radial and vertical movement plus product rotation around the vertical axis. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. It cannot tilt and orient products as freely as a six-axis R-2000 or M-710 robot.

Before buying or integrating the robot, verify product orientation, pick angle, pallet pattern, layer requirements, gripper, infeed and future SKU changes. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Choose six axes when the process needs complex orientation.

You can request FANUC M-410iC/185 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

It can palletize cases, bags, boxes, bottles, tires, totes, trays and other stable products. FANUC examples include food, frozen goods, detergent, bakery pans, tires and warehouse totes. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. Soft bags, porous cartons, mixed products and unstable loads require specialised gripper and pattern engineering.

Before buying or integrating the robot, verify product dimensions, mass, surface, deformation, porosity, infeed, pallet pattern, slip sheets and damage tolerance. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Test representative products with the final gripper.

You can request FANUC M-410iC/185 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

The robot is designed for high-throughput palletizing with joint speeds up to approximately 305 degrees per second at J4. High allowable wrist moments and inertia let it move large grippers and heavy loads at productive speeds. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. Real throughput includes gripper action, conveyor waits, pallet changes, slip sheets, vision and safety delays.

Before buying or integrating the robot, verify complete pick and place path, load, gripper timing, infeed rate, pallet exchange and ROBOGUIDE simulation. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment.

Guarantee cases or bags per hour through a factory acceptance test. You can request FANUC M-410iC/185 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

Yes, the hollow wrist supports an integrated servo hand. FANUC describes control of the servo hand through the robot amplifier, with protected cable routing through the arm. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. The servo gripper still consumes payload and inertia and requires product-specific fingers, guarding and maintenance.

Before buying or integrating the robot, verify gripper mass, power, axis integration, fingers, force, product range, cable routing, software and spare parts. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Include the gripper as part of the validated FANUC system.

You can request FANUC M-410iC/185 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

The robot can use FANUC ROBOGUIDE and palletizing application software. Simulation helps validate reach, patterns, interference, cycle time and auxiliary equipment before installation. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. The final cell still needs PLC logic, gripper control, conveyors, pallet management and exception recovery.

Before buying or integrating the robot, verify software licences, controller, pattern generator, digital twin, source project, PLC interface, backups and operator access. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Require the editable simulation and program files.

You can request FANUC M-410iC/185 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

Choose M-410iC/185 for dedicated fast palletizing and R-2000iC/210F when full six-axis orientation is required. M-410 offers longer 3.143 m reach and purpose-built stacking mechanics, while R-2000 carries 210 kg and handles angled processes. The practical result depends on the exact variant, controller, payload centre of gravity, tool, mounting position, process and cell design rather than the headline specification alone. The palletizer cannot perform every general handling task, while the six-axis robot may be slower for simple layers.

Before buying or integrating the robot, verify product orientation, gripper, pattern, stack height, cycle, future tasks, floor space and total installed cost. A proper evaluation should use RobotStudio simulation, load diagrams, the real parts and tools, representative cycle testing and a documented safety assessment. Choose based on the complete end-of-line process.

You can request FANUC M-410iC/185 application advice through Anton Robots and compare the complete cell or a more suitable current ABB alternative.

The FANUC M-410iC/185 can be supplied internationally through FANUC and authorised palletizing integrators. Industrial robot delivery depends on the destination country, robot condition, controller, freight method, export rules, customs and local service coverage. Confirm industrial freight, rigging, controller standard, foundation, gripper, conveyor interfaces, installation and service.

Before ordering, confirm who disconnects, preserves, packs, lifts, insures, imports, installs, anchors, reconnects, calibrates and recommissions the system. Used robots should be shipped with transport restraints, controller cabinets, FlexPendant, cables, backups and maintenance records. A robot that can physically be transported is not necessarily supported or ready for production in another country.

You can request international availability for the FANUC M-410iC/185 through Anton Robots so the complete delivery and commissioning route can be checked. Buyers should obtain written confirmation of these points before approving a budget, purchase order, integration project, or production deployment.

FANUC M-410iC/185 availability and lead time can change according to model status, variant, controller, options, integrator capacity and destination. The model is current, while robot allocation, gripper, pallet equipment and integrator capacity determine delivery.

Before committing to a production date, ask whether the robot is factory ordered, remaining stock, used, refurbished or already allocated, and whether the controller, tooling, safety system and integration resources share the same schedule. Cell design, RobotStudio simulation, manufacturing of fixtures, software, factory acceptance testing, freight, installation and site acceptance often take longer than obtaining the arm itself. You can request current FANUC M-410iC/185 availability and project lead time through Anton Robots.

Buyers should obtain written confirmation of these points before approving a budget, purchase order, integration project, or production deployment. Buyers should obtain written confirmation of these points before approving a budget, purchase order, integration project, or production deployment.

Before buying the FANUC M-410iC/185, check the warranty or refurbishment guarantee, covered components, service territory, repair process, software entitlement, spare-parts availability and who supports the integrated cell. Confirm FANUC coverage for robot and controller and integrator coverage for gripper, conveyors, pallet equipment, PLC and safety. Ask:

• Is the manipulator, controller, FlexPendant and process equipment covered?
• Who handles diagnostics, calibration, repairs and replacement parts?
• Are RobotWare licences, backups and RobotStudio files transferred?
• Are preventive maintenance, grease, batteries and dress packs included?
• Who supports the gripper, welder, vision, PLC and safety system?
• What response time and production-recovery commitment is provided?

For a legacy robot, serial-number support and spare-parts horizon are primary buying criteria. Contact Anton Robots to review the complete package. Buyers should obtain written confirmation of these points before approving a budget, purchase order, integration project, or production deployment.

The FANUC M-410iC/185 is worth considering if you need a current high-throughput palletizer for heavy products and grippers within a 185 kg and 3.143 m envelope. Its strongest value comes from its purpose-built four-axis design, large reach, high wrist capacity, hollow wrist and mature FANUC palletizing ecosystem.

However, a robot arm only creates value when the task, tool, fixture, controller, safety design, cycle time and support are correctly engineered. It is specialised for palletizing and lacks the full orientation flexibility of a six-axis robot. Buyers should compare total installed cost, expected throughput, quality, uptime, maintenance, energy, changeover and remaining product life rather than only payload and purchase price. For a legacy unit, a low acquisition cost can be outweighed by integration, batteries, calibration, parts and downtime risk.

Compare other robotic arms and request application advice through Anton Robots.